Wednesday, May 23, 2012

The Penny Trick! Solves HP Black Screen No Video Output


This repair can garder from $50- $100 cash profit. After the initial $55 material cost any future work of this kind costs only a penny. So for one penny and about an hours work you can make up to a hundred dollars. Hence I call this the Penny Trick. 

HP made a big mistake on the DV9000 and DV6000 models. A year or more after purchasing on of these laptops the video output will go completely out. The LEDs and will light up showing the computer's on, but the sad screen will stay completely blank. Many shops will take the easy way on this one and replace the entire motherboard. It's unnecessary. Let's point the finger at the real problem child here, the GPU or Graphics Processor. When these laptops heat up the solider connecting the video chip to the board weakens and loses connection. An inadequate heat sink is the usual culprit. The same thing happens to the Xbox with the RROD or Red Ring of Death.


Items Needed:
  • A Digital Probe Thermometer ---$20
  • Thermal Compound                ---$5
  • Butane Torch                          ----$25
  • Aluminum Foil                        ----$1
  • Scotch tape                              ----$1
  • Small Screw Driver                 ----$1
  • A Penny                                  ---$0.01 


Okay before you go to town pulling the 50 some odd screws it's going to take to get the motherboard out I must note- be cautious to prevent ESD. Electrostatic Discharge or simply static shock could damage your board especially the RAM. If affordable buy a wrist strap and ground yourself. Other wise at least touch metal to ground yourself before you begin. Also I take no responsibility for these plans- Procede with Caution.

With that out of the way take your small screw drive and disassemble the laptop down to the motherboard. Take the heat sink off paying close attention to what chips it's covering. Definitely make certain to take off the processor and the RAM.  Of course remembering where every cable part goes, take notes if necessary. With the board out in front you'll need to identify where the GPU is. On most boards it will be close to the processor and most likely covered by the same heat sink. If in doubt look it up. 

Now cut a piece out of the foil about twice the size of the chip. You'll want this to be two layers if not three. Press this piece of foil against the chip to get a good indentation or imprint. Cut out that imprint so this will fit nicely around the chip. Now tape the outsides of the foil to keep it in place. This is done to cover the surrounding board from the flame.

Next turn on the digital probe and set it to fahrenheit. Tape the metal part of the probe directly behind the chip on the other side of the board. Since you may want to hold the board steady, use an oven or something similar to hold the side taped to the monitor.

Now comes the fun. Light up the torch. We're not trying to fry the board here. Only heat the GPU to a certain temperature to reconnect the existing solder under the chip. Similar to reballing except not taking the chip off. Bring the torch down to an acceptable level to heat the chip and not burn the surrounding components. Watch the temp and take it up to around 220f. The whole time keeping the flame circulating to even out the heat. Much hotter you'll burn the chip, any less the solder won't completely melt. Only keep it at that degree for a few seconds, then let it cool off. 

After the board's cooled off apply the thermal compound to the back of the chip and to the back of the processor. Now to ensure that heat doesn't cause this problem again. Place the penny on top of the video chip and replace the heat sink on top of that. While not absolutely necessary, this helps the heat dissipate off the chip and ensures this fix will last much longer. If it's to tight of a squeeze a copper shim works fine as well. Am I the only one that thinks it's funny to have a penny inside a laptop? Just to assist here's a vid with a similar fix:



13 comments:

123contract said...

Computer Support Sydney City

I have read all the article,and i want to say thanks to you for exceptional information

claudia shaw said...

IT Support Services are not only for the IT sector, but they have become an integral part of all kinds of businesses worldwide.
it support herts

Jeff Hardy said...

thanks for this informative post. Now you can use this directory of companies in india to promote computer hardware products import & export business.

Computer repair said...

Its good to get information like this and it really helps a lot in practical day to day life.

Rusty Jalz said...

This service is available 24x7. Unlike the traditional computer repair services, the computer support is available at any hour of the day.

Anonymous said...

immoldiff immoldiffJB
Peyton Manning Orange Jersey
Authentic Frank Gore Jersey
jerrey rice jersey

Anonymous said...

Hi friends, how is everything, and what you want to say concerning this piece of writing, in my view its genuinely amazing in
favor of me.

Take a look at my web blog read more

Anonymous said...

visit homepage propecia hair loss - propecia cancer

Chris Barsby said...

Just found this purely out of interest looking up about the Penny Trick. An alternative if the solder has come loose is reflowing.

Preheat an oven to about 220c, pop the motherboard on an upside down overtray, and pop it in for 10 minutes.

I normally turn the oven off after 8 minutes, let the heat thats inside continue its work. After another 2 minutes, open the oven and let it all cool down and what not.

Leave the motherboard in to cool for a bit, as moving it could disconnect solder again due to it still be fairly loose.

It's a good alternative to try BEFORE going and buying the equipment to do some of this sort of thing, as it doesn't cost a penny!

I've fixed numerous laptop boards with solder issues this way.

computer networkzone said...

Soon after look at a couple of of the weblog posts on your web website now, and I actually like your indicates of running a blog. I bookmarked it to my bookmark world wide web site document and will most likely be examining once again soon. Make sure you check out my web web site as effectively and allow me know what you think.
long beach computer repair service
mac repair

Jane Fairfax said...

This is a neat computer repair trick. I'm not tech-savvy, but even I can do this. It's nice to know that I am picking up these tricks to troubleshoot small issues. Still, the bigger things I am saving for the professional repair guys.
http://www.simplifiedcomputers.com/services_in_store.html

Adam Dalena said...

Very informative post. Thanks for share useful information.

laptop repair lake worth

MANIKANDAN R said...

Hi,

It's really Great... Thanks for share this information.... I just had little bit of experience from this blog......
paper cup suppliers in chennai